Coverage from solids & DFT
API · /coating-api
Industrial Coatings API
degraded
3,042 Subscribers
Industrial and protective-coatings maths as an API, computed locally and deterministically — the film-build numbers a coatings inspector, painter or estimator works to, the ones simple paint estimating skips. The coverage endpoint gives theoretical and practical coverage from the coating's volume solids and the target dry film thickness: coverage = 1604 × the volume-solids fraction ÷ the DFT in mils, where 1604 is the square feet a gallon covers at one mil — so a 50 %-solids coating at 2 mils dry covers about 401 ft² per gallon, less a loss factor for overspray and surface profile. The film-thickness endpoint converts between wet and dry film thickness through the volume solids: WFT = DFT ÷ the solids fraction, because the solvent flashes off and the film shrinks, so a 50 %-solids coating laid 4 mils wet dries to 2 mils — the number you check with a wet-film comb as you spray. The transfer-efficiency endpoint gives the real material needed: theoretical gallons ÷ the transfer efficiency, since conventional spray lands only ~25 % on the part, HVLP ~65 %, electrostatic up to ~95 %. Everything is computed locally and deterministically, so it is instant and private. Ideal for coatings-estimating and inspection apps, industrial-painting and protective-coating tools, NACE/SSPC study aids, and spec calculators. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 compute endpoints. For simple wall-paint area estimating use a paint API.
api.oanor.com/coating-api
API health
degraded- Uptime
- 91.67%
- Server probes · 24h
- Avg latency
- 87 ms
- Server probes · 24h
- Subscribers
- 3,042
- active
- Total calls
- 4
- last 7 days
Pricing
Pick a tier — billed monthly, cancel anytime.
Free
Free
- 440 calls / month
- 2 requests / second
- Hard cap (429 above quota, no overage)
- 440 calls/month
- 2 req/sec
- Coverage + film thickness + TE
- No credit card
Starter
€5.65 /month
- 11,800 calls / month
- 6 requests / second
- Hard cap (429 above quota, no overage)
- 11,800 calls/month
- 6 req/sec
- Volume-solids & WFT/DFT
- Email support
Pro
€17.90 /month
- 76,500 calls / month
- 15 requests / second
- Hard cap (429 above quota, no overage)
- 76,500 calls/month
- 15 req/sec
- Estimating & inspection pipelines
- Priority support
Mega
€53.00 /month
- 252,000 calls / month
- 36 requests / second
- Hard cap (429 above quota, no overage)
- 252,000 calls/month
- 36 req/sec
- Platform scale
- Dedicated SLA
Built by
Related APIs
Other APIs with overlapping tags.
Air Compressor API
Compressed-air maths as an API, computed locally and deterministically — the receiver, pump-up and SCFM numbers a pneumatics tech or shop owner sizes a system with. The receiver-size endpoint gives the tank you need to ride out a demand burst: volume = demand (free-air CFM) × minutes × 14.7 ÷ the usable pressure window (max − min) — pulling 20 CFM for a minute over a 175-to-100 psi window wants about a 30-gallon receiver, the buffer that lets the pump catch up. The pumpup endpoint gives the time to raise a receiver from one pressure to another: volume × pressure rise ÷ (14.7 × compressor CFM), so a 60-gallon tank from 100 to 175 psi on a 15 CFM compressor takes about 2.7 minutes. The scfm endpoint corrects actual CFM to standard CFM for the inlet conditions — SCFM = ACFM × (inlet pressure ÷ 14.696) × (528 ÷ inlet temperature in Rankine) — so a compressor at 5,000 feet delivers about 17 % fewer SCFM than at sea level, the reason you size tools on SCFM, not the nameplate. Everything is computed locally and deterministically, so it is instant and private. Ideal for pneumatics and shop-air apps, compressor-sizing and tool-demand tools, industrial-air calculators, and trade aids. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 compute endpoints. Estimates — duty cycle and the pump curve shift real numbers.
api.oanor.com/compressor-api
Tank Volume API
Tank volume and fill-level maths as an API, computed locally and deterministically. The volume endpoint gives the total capacity — in litres, US gallons and cubic metres — of a vertical cylinder, horizontal cylinder, rectangular tank, sphere or capsule, from its dimensions in metres, centimetres, millimetres, feet or inches. The fill endpoint computes the volume of liquid and the percent full at a given fill depth, using the exact geometry for each shape — including the circular-segment formula for a horizontal cylinder (where the level is famously non-linear) and the spherical-cap formula for a sphere. The level endpoint is the inverse "dipstick" calculation: it finds the depth that corresponds to a target volume or a target percentage, solving the segment geometry by bisection. Everything is computed locally and deterministically, so it is instant and private. Ideal for fuel, water, oil and chemical tank monitoring, agriculture and irrigation, process and industrial tooling, and tank-gauging and dipstick apps. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 endpoints. This is tank-gauging geometry; for swimming-pool volume and chemical dosing use a pool API, and for plain unit conversion use a unit-conversion API.
api.oanor.com/tank-api
Ladder Safety API
Ladder-safety maths as an API, computed locally and deterministically — the angle, reach and load numbers that keep a ladder from sliding out or buckling. The angle endpoint applies the 4:1 rule: the base goes out one foot for every four feet of working length, which lands the ladder at about 75.5° — a 24-foot ladder sits 6 feet from the wall and reaches roughly 23 feet up, steep enough not to tip back and shallow enough not to slide. The extension endpoint gives the usable length and reach of a two-section extension ladder, which loses the overlap the sections share (3 feet up to 36, 4 to 48, 5 beyond), and the working height at the safe angle — remembering the ladder must extend 3 feet above a roof edge you step onto. The duty-rating endpoint turns a total load — your weight plus tools and materials, not just bodyweight — into the right duty class, from Type III household (200 lb) through I industrial (250) to IAA professional (375). Everything is computed locally and deterministically, so it is instant and private. Ideal for construction-safety and trades apps, jobsite and rental tools, OSHA training aids, and home-improvement sites. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 compute endpoints. Educational — always follow the manufacturer's labels and OSHA/ANSI rules.
api.oanor.com/ladder-api
HVAC Ductwork API
HVAC duct-sizing maths as an API, computed locally and deterministically — the duct dimensions an installer or designer sizes a system with so the air moves quietly and efficiently. The round-duct endpoint gives the round duct for an airflow at a target velocity: area = airflow ÷ velocity (CFM ÷ ft/min = ft²), then diameter = √(4·area/π) — 400 CFM at a 700 fpm trunk velocity wants about a 10.2-inch round, rounded up to the next 12-inch trade size. The velocity endpoint gives the air speed inside a duct from the airflow and its size, round or rectangular — 400 CFM through a 12 × 8 duct runs at 600 fpm, comfortably quiet, while the same air in a 10-inch round moves at 733 fpm. The equivalent endpoint gives the equivalent round diameter of a rectangular duct by the ASHRAE relation De = 1.30 · (a·b)^0.625 ÷ (a+b)^0.25, so a 12 × 8 rectangular carries the same air at the same friction as a 10.7-inch round — letting you size on a round friction chart and convert to fit the space. Everything is computed locally and deterministically, so it is instant and private. Ideal for HVAC-design and installer apps, duct-sizing and takeoff tools, building-services calculators, and trade-school aids. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 compute endpoints. For room air changes use a ventilation API; for the cooling/heating load use an HVAC API.
api.oanor.com/ductwork-api
Frequently asked questions
Quick answers about pricing, quotas, and integration.
How do I get an API key for Industrial Coatings API?
Sign up for free at oanor.com, generate an API key from the developer dashboard, and call Industrial Coatings API with the x-oanor-key header. No credit card needed for the free tier.
What's the rate limit for Industrial Coatings API?
Free tier allows 1 request per second. Paid plans scale up to 50 requests per second on the Mega tier. Hard limits return HTTP 429 above the quota — no surprise overage charges.
How much does Industrial Coatings API cost?
Industrial Coatings API has a free tier with 100 calls / month. Paid plans start at €5.65 / month with higher quotas and faster rate limits.
Can I cancel my subscription anytime?
Yes. Plans are billed monthly and you can cancel anytime from your billing dashboard. No long-term contracts and no cancellation fee.
Is Industrial Coatings API GDPR-compliant?
All requests to Industrial Coatings API go through our EU-based gateway. Your upstream API key never leaves our server and no personal data is shared with the upstream provider beyond the request you send.
Pick an endpoint from the list on the left to see its details and try it.
Code snippets
Sign up to get an API key, then call any path under your slug.
curl https://api.oanor.com/coating-api/SOME_PATH \
-H "x-oanor-key: oanor_test_..."const res = await fetch("https://api.oanor.com/coating-api/SOME_PATH", {
headers: { "x-oanor-key": "oanor_test_..." }
});
const data = await res.json();$ch = curl_init("https://api.oanor.com/coating-api/SOME_PATH");
curl_setopt($ch, CURLOPT_RETURNTRANSFER, true);
curl_setopt($ch, CURLOPT_HTTPHEADER, ["x-oanor-key: oanor_test_..."]);
$response = curl_exec($ch);import requests
r = requests.get(
"https://api.oanor.com/coating-api/SOME_PATH",
headers={"x-oanor-key": "oanor_test_..."},
)
print(r.json())Ratings
Sign in to rate.
No reviews yet.
Discussion
Ask questions, share usage tips, get answers from the provider and other developers. Public — anyone can read.
Sign in to start a thread or reply.
Sign inNew thread
📌 Pinned
🔒 Locked
·
·
·
-
Provider answer
🔒 This thread is locked — no new replies.
-
·
- No threads yet — start the discussion.
Support
Private 1:1 support with the provider — billing questions, integration issues, account problems. Only you and the provider team can see these threads.
Sign in to open a support ticket.
Sign inOpen new ticket
Describe what you need help with. The provider team gets an email and replies on the ticket page.
-
·
Urgent - No tickets yet for this API.